Quality management

The Meiser Quality Management System has been developed as a holistic approach.

Our goal is to safeguard and develop the product characteristics based on our customers’ demands. Special attention is given to careful product development. Defects are recognized early and avoided constantly in order to prevent any problems during production.

If a defect still occurs, it can be analyzed with the Meiser QM System; this way the defect can be corrected and completely eliminated for further processing steps. The Meiser QM System supports a dynamic learning process with the objective to avoid defects effectively.

The most important modules of our Quality Management System are:

  • Textile lab with sampling machines
  • IT controlled processes during processing
  • Constant quality control according to ISO standards
  • Result documentation
  • Stipulation and analysis of objectives
  • Joint responsibility of the process by each employee
  • Quality management manual

 

Our quality management system is certified according to DIN EN ISO 9001. 

We are looking forward to inspire you with our quality management philosophy!

Continuous Improvement Process

CIP refers to an internal attitude of all process steakholder; this philosophy achieves continuous improvement with long-lasting effects.

CIP is being implemented in all processes of our company. Our focal points are:

Quality of products

Quality of processes

Quality of service

Small improvements are constantly developed from continuous teamwork and are implemented immediately. Our goal to achieve effective benefits for our customers determines our actions and secures the development of more efficient and lean structures.

To increase customer benefit and to avoid problems in the long run each improvement has to be integrated into the daily work routine.

Resource Management

Sustainable use of resources is the basis of our company’s internal resource management system.

Sustainability means, for us, the prudent application of energy and raw materials. At all points of added value, this guideline is consistently integrated into product planning. We especially focus on the following:

  1. No, or little, pollution through emissions (exhaust, wastewater, waste air)
  2. Chemicals (Threshold Limit Value/TLV)
  3. Skin compatibility


The most important input factors are compiled in an environmental auditing and evaluated on a monthly basis. Based on this environmental analysis we can take decisions to improve the environmental compatibility of our production.

Meiser places emphasis on the following measurements for environmental protection:

  • Reduction of energy demand
  • Reduction of water demand
  • Processing of wastewater to transfer back to the public sewage plants
  • Reduction of organic and inorganic pollution
  • Processing of waste air
  • Usage, safety, storage and transport of chemicals
  • Waste and recycling of waste materials

Made in Germany

Transparency Builds trust.

These days consumers rightly demand the transparency to know where purchased products are manufactured and produced. In the textile production chain this is hardly evident. For this reason we have been member of the „Made in Germany“ initiative for many years.
 
We have our own seal ID to provide our customers with the possibility to lable their own products for end-consumers in a transparent kind of way. This seal ID including logo is provided by us for customers producing stretchy knit fabrics in Germany only.

Facts:

  • Carl Meiser GmbH & Co. KG solely produces in Germany.
  • The seal can only be used for tubular fabrics knitted and treated in Germany.
  • The seal ID is 627.


We’ll be glad to advise you on possibilities of labeling and marking your products.
Please feel free to contact us.

Innovation Award

Prize winner of the Innovation Award of the State Baden-Württemberg.

As a leading innovative company, nopma Technical Textiles offers solvent-free PU adhesive systems as pre-coatings before lamination. With this patent-registered adhesive system nopma adhesion light, the company Carl Meiser is prize winner of the innovation award 2011 of the state Baden-Württemberg.

The initial position

During the last few years, there has developed the upward trend of valorizing the automobile interior. As a result of this development there is a greater variety of materials, more complex shapes and higher haptic requirements already for upper middle-sized classes.

The manufacturers of interior parts like for example a center console have to cope with various problems during the lamination process:

  • Compliance with emission value in vehicle interior
  • Long/not appropriate cycle times
  • Deterioration of the backing material due to too much heat
  • Discard due to irregular layer of adhesive
  • Expensive equipment like robots and other machines for the adhesive application
  • ...or alternative high manual input
  • Inflexible material by adhesive coating
  • Much filling waste due to cutting first during lamination
  • Discard due to irregular layer of adhesive

and other process specific problems and risks.

The Innovation

The very special about nopma adhesion light is that company Carl Meiser managed to apply a solvent-free adhesive on a great width with precisely defined application quantity by own development of machines and machine elements.

Owing to great simplification of the customer`s process, the lamination of complex interior parts is possible at greatly reduced costs. Until now such complex parts were only possible in small series with high manual effort.

Download: Award 2011

Solar power station

We count on renewable energy.

Bothe areas of operation of the company Carl Meiser GmbH&Co.KG - Meiser Textile Finishing and nopma Technical Textiles - run very energy intensively and need permanent steam heat supply. Today, the steam heat is 100% obtained from fossil fuel.

Together with company Smirro GmbH, company Carl Meiser works against this dependence by installing a first test plant of ca. 100 m² solar collectors on the company roof.

The very special about this project is that the collectors developped by Smirro are able to produce local solar process heat up to 240°C, which will 100% be used in the production.

This pilot scheme is supposed to test and demonstrate what renewable energy is able to accomplish.

Feedback

Your opinion is important to us!

To optimize and improve our processes for you on a continuous basis we need your feedback. Please address issues that need improvement. We are looking forward to speak with you directly. As an alternative we offer you our CIP-Feedback-Questionnaire.

We would love to hear your suggestions!

OpenClose form

Please rate our accomplished services or delivered products by the following criteria.

  • 1
  • 2
  • 3
  • 4
  • 5
Innovation competence
Self-initiative and Motivation
Collaboration
Productivity and flexibility
Reliability
Technical competence
Quality
  • 1
  • 2
  • 3
  • 4
  • 5
Adherence to schedules
Cost-benefit ratio
Service
Documentation
Systemcapability
Quality of offers
Kindness

1=exemplary accomplishment, 2=equitable solution, 3 solution accomplished with additional support, 4=solution accomplished based on support, 5=Expectation not fulfilled 

Would you use our services again?

Um auch für Sie weiterhin ein attraktiver und kompetenter Partner zu sein, bitten wir um Ihre Meinung und Ihre Anregung. Wie ist Ihre kurzfristige und langfristige Erwartungshaltung?

Wie können wir unsere Leistungsfähigkeit kurzfristig und langfristig erhöhen, was müssen wir bewegen?